[Jiuzheng Building Materials Network] Toilets are a space that every family has, and most of them are shared by bathroom and bathroom. However, certain things can still be installed. Bathroom hardware is very common and necessary, so how can bathroom hardware be simply installed? What are the cleaning and maintenance methods for hardware? Don't worry, let's take a look at Jiuzheng Hardware Network

The bathroom is a space that every family has, and most of it is shared by the bathroom and bathroom. However, some things are still installed. Bathroom hardware is very common and necessary, so how to install bathroom hardware easily? What are the cleaning and maintenance methods for hardware? Don't worry, let's take a look at Jiuzheng Hardware Network.

How to install bathroom hardware easily?

For daily convenience, the installation of bathroom hardware should not only pay attention to its installation position and height, but also pay attention to whether its installation quality is qualified. In particular, bathroom hardware pendants that require drilling wall holes can easily fall off and damage the wall if they are not installed in place. Reinstallation will also affect the aesthetics of the wall. Next, let's take a look at how to install various bathroom hardware.

the floor drain

If the floor drain is not installed in place, it may cause odor and water overflow. The center line of the main core of the floor drain must coincide with the center line of the pipeline to ensure that the product always maintains the highest drainage efficiency. Floor drains should be slightly lower than the ground to avoid water accumulation, and they must be located at the lowest point on the floor. During the entire decoration process, various foreign matters should be avoided, especially cement slurry entering the pipeline through the floor drain, which can avoid blocking the pipeline in the home due to the entry of decoration waste.

shower head

When installing a sprinkler, first determine the height of the sprinkler mixing valve from the ground. Generally, we control it within a height range of about 90~100cm. When laying pipes, the reserved position of the shower faucet should be considered clearly, generally 15mm higher than the rough wall, so that when the tiles are finished, the thread head can be buried to ensure the beautiful wall. The spacing reserved for the inner wire elbow of the shower is generally about 10-15cm.

Storage rack

The height of the storage rack should be controlled below 190CM, as the place where the human hand can reach is around 110CM, so it is most appropriate to place the storage rack at around 110CM. It is best to use an impact drill for punching the shelves, which is more reliable. Secondly, it is best not to tilt during installation. It is best to use waterproof materials and glass glue for nailing positions, to avoid hitting the tiles too deeply and breaking them.

Wash basin faucet

The faucet is an indispensable part of the washbasin. How to install the washbasin faucet? The gasket is used to relieve the pressure on the metal surface of the faucet to contact the ceramic basin, protect the ceramic basin, and then insert and tighten a water inlet pipe. Thread the threaded joint into the first water inlet hose, and then thread the water inlet end of the second water inlet hose through the threaded joint. Screw the second water inlet hose into the water inlet port, paying attention to the correct direction.

Washing machine tap

Press and hold the lower end of the locking rod down on the slider and remove the water inlet pipe connector from the water inlet pipe component. Tear off the tag above and confirm that the thread is exposed by about 4mm. If it is less than 4mm, loosen the nut to make it reach 4mm. Loosen the four screws of the water inlet pipe joint until they can be sleeved onto the faucet, and then sleeve the water inlet pipe joint onto the faucet. Tighten the four screws on the water inlet pipe connector.

mirror

Use a tape measure to measure the distance between the center points of the two hooks. Use a tape measure to measure the width and height of the wall, and use a pencil to mark the positions of the two center points. Use a prepared impact drill to drill holes at the marked center point, with a depth of about 5cm for a 6mm-8mm drill bit. Use a hammer to drive the expansion screw into the drilled hole. Use a screwdriver to screw the screw into the expansion screw, leaving a distance of about 5mm from the wall.

Soap dish holder

Wipe the wall clean, without any stains or oil stains. Remember to make sure the wall is flat. Generally, bathrooms are made of ceramic tiles, which is fine. Do not paste it in the intersection gap! Then we stick the adhesive side of this soap box to the wall first, and then press it against the wall clockwise by hand until there is no air inside! After the suction cup is pressed and installed, fit this soap accessory into the hole and fasten the soap box.

Toilet paper box

The height of the toilet paper box is generally around 760 mm, and the distance from the toilet pan is generally around 300 mm. In fact, toilet paper boxes are generally installed using suction cups, but everyone must purchase a high-quality suction cup when purchasing. Of course, hooks can also be used, and the quality of the same hooks must pass the standard. It is recommended that everyone go to the supermarket to buy them. The last method is to use glue to stick the toilet paper box onto the wall.

Soap dispenser

The best location for installing a wall mounted soap dispenser is 30 centimeters above the washing table on the left or right. Determine the location of the drilling hole, and install a rubber plug when installing screws, which can protect the wall hole from falling debris and no longer expanding. If an automatic soap dispenser is installed, check whether the motor wires and sensing head cables are properly connected and installed firmly after installation; The power plug should be connected to the water source to avoid safety accidents.

a hook

Install a clothes hook in the middle of the bathroom, where you can hang towels, bath towels, various toiletries, or sachets, to better ventilate and drain the towels, and the sachets can better emit fragrance to maintain the freshness of the bathroom. Generally speaking, the installation height of the toilet clothes hook is usually about millimeters above the minimum family height. The clothes hook is installed on the right side of the mirror, making the handling of towels more comfortable and convenient.

Hand dryer

The installation height of hand dryers is generally 1.2 meters from the ground. Generally, people who have children in their homes can buy a floor mounted upward baking phone. If you don't have children, you can use a general household type hanging dryer phone and install it according to your height. This way, it can be convenient for the entire family to use. Generally speaking, it is installed next to the bathroom as the best location to ensure that you can enjoy the dry hand service after washing your hands.

Cleaning and maintenance methods for hardware:

The bathroom is relatively humid and prone to dirt. In addition to paying attention to the cleaning and maintenance of large items such as bathroom fixtures, the cleaning and maintenance of bathroom hardware should not be ignored. Due to the residual presence of various shampoos, shower gels, and water stains on the surface of hardware used at ordinary times, the luster of bathroom hardware deteriorates, and even rusts and falls, directly affecting the use of bathroom hardware.

water tap

After installing the faucet in the bathroom and using it for a period of time, it will be found that the surface of the faucet is prone to residual water stains, which can form very ugly spots after drying. If the faucet is not cleaned for a period of time, even if it is high-grade, it will become overshadowed, so we must regularly clean and maintain the faucet. For scale and rust on the faucet, just wipe the surface with a damp cloth or sponge dipped in a small amount of special cleaning agent, and then rinse it with water.

shower head

In life, poor water flow from flower sprinklers is a frequent cause, so we should master some small techniques and timely clean up to make the water flow smoother. Remove the mesh cover or other components that adsorb scale from the shower head, and immerse the shower in a solution of 50/50 white vinegar and water. The white vinegar can easily remove mineral deposits. After cleaning with a brush, install it back in place. In addition, many sprinklers are equipped with the function of automatically removing scale.

the floor drain

Cleaning the floor drain regularly can prevent the floor drain from backsmelling. Clean the debris on the partition; Remove the floor drain filter screen and clean the accumulated debris and hair on the filter screen; Prepare warm water diluted with baking soda powder, and soak the floor drain separator, filter screen, and other accessories in warm water; After half an hour, remove all accessories, use an old toothbrush to brush the dirty area, and then rinse with clean water; To disinfect and deodorize the sewer, you can use soda solution or hydrogen peroxide plus water to clean the sewer.

Storage rack

Due to the long-term residue of various shampoos and shower gels used in daily use on the chrome plated surface, the surface gloss of the shelf will deteriorate and directly affect the surface quality. Please clean the shelf surface with a soft cloth at least once a week, preferably using a neutral detergent. You can use a pure cotton wet cloth coated with toothpaste and soap, gently wipe it, and then wash it with clean water. Wipe the shelf with clean water and dry it with a soft cotton cloth. Do not use any abrasive cleaning agent.

mirror

The mirror has been exposed to moisture for a long time, resulting in blurred imaging and water stains. Before taking a bath, you can smear soap onto the mirror surface and wipe it with a dry cloth. A layer of soap liquid film is formed on the mirror surface to prevent blurring of the mirror surface; Use a dry cloth dipped with an appropriate amount of detergent to smear on the mirror surface, and evenly wipe it away. The active ingredients contained in Xijie Ling can effectively prevent condensation of water vapor on the mirror surface, and can play a good antifogging role. There are also coated antifogging mirrors and electric antifogging mirrors available on the market.

Soap dispenser

After using the soap dispenser for a period of time, dust or water stains cannot be avoided. After being idle for a period of time, some soap liquid may condense in the soap dispenser. If the amount of soap liquid is small, stir it with warm water, which can reduce the soap liquid to a liquid. If the above method is not feasible, remove the condensed soap liquid, add warm water, and use the soap dispenser multiple times until warm water dries out of the soap dispenser. This can clean the entire soap dispenser.

Hand dryer

Regularly clean the dust and dirt outside the hand dryer, and wipe it with a dry soft towel or wet cloth; The front filter screen (usually the rear cover of the chassis) should be cleaned 1-2 times a month. Remove the filter screen, pat it or blow it clean with a hair dryer, or even wash it with clean water, dry it, and then install it into the panel; The best maintenance method for formaldehyde filter screens is to regularly expose them to the sun. Activated carbon filter screens, which require regular replacement, are disposable consumer goods.

Tissue holder

The toilet tissue holder is located next to the toilet or squatting pan, which can easily contaminate bacteria and affect the appearance. So, how do we clean and maintain the tissue holder? You can use a special maintenance cloth for a paper towel rack or a pure cotton cloth to wipe the water off the pendant. Remember to immediately remove all cleaning agents with clean water and wipe dry with a dedicated maintenance cloth (or pure cotton cloth) for the pendant after each cleaning, otherwise water stains and dirt may appear on the surface of the pendant.

Soap dish holder

Soap dishes have been used for a long time, and the degradation of surface gloss directly affects the quality of use. Therefore, clean the surface of the soap dish with a soft cloth at least once a week, preferably using a neutral detergent. For stubborn scale, surface scale film, and stains that are difficult to remove, please use a mild liquid cleaner, then clean with clean water and wipe dry with a soft cotton cloth. Do not expose soap dishes to the sun. Do not put heavy objects into the suction cup soap box.

a hook

Hooks are mostly curved or angled hooks made of metal or other tough materials to hook items such as clothing and towels. Pay attention to the standard load bearing of the hook, and do not change the purpose or use it over weight. Do not wash the hook with alkaline water or boiling water to prevent damage to the paint surface. Regularly clean the surface of the product with clean water or a mild detergent, and then wipe it dry with a soft towel. To maintain a smooth and bright appearance, do not use a detergent based on salt or vinegar.

three-way valve

Wash away the simple stains on the corner valve with clean water. For stains that are easily removed, they can be cleaned with clean water. Avoid contact with strongly acidic substances. The material of the angle valve is mostly brass, alloy, iron, plastic, etc. Contact with strongly acidic substances can cause chemical reactions that can damage the angle valve. Clean the stubborn stains on the corner valve with a gentle cleaning product. For stains that are difficult to remove, use a mild, neutral liquid or colorless glass cleaner to clean.